Re: Ping Sensor - pinMode too slow? (both Arduino and MRAA)
Kurt, thanks for the dribble. If I started a private Yahoo group, would you be interested in joining it? I'm a robotics guy, retired mech engr from Northrop-Grumman, etc. Not professional, but as a...
View ArticleRe: Error [00000524] upgrading Proset "The specified account already exists"
Thanks Joe, I saw this thread but as the description of the error was different I didn't think it would resolve my problem.I found the files Wifi.msi and Wifi.cab files in the temp directory and copied...
View ArticleRe: How to enable ppp in kernel mode / rebuild the kernel with ppp?
arfoll I downgraded my Ubuntu to 12.04, to be on the safer side. cant share the log files
View ArticleRe: Not possible tp use Yocto Linux with "Tera Term" oder "Cool Term"
No I wasn't. I tried to connect with the Galileo as it is discribed on Galileo Getting Started Guide - learn.sparkfun.comThere is a chapter "Using the Terminal" and I tried to connect using the...
View ArticleHelp in executing opencv binary on galileo debian 1.2 image
hi I am working on my galileo board with the debian 1.2 image on it. I am new to linux so am not good in commands. I have installed the image on an sd card using win32disk manager and it runs good on...
View ArticleRe: Windows media center and intel 4600 graphics live tv stutter
Hi Allan. Please pass on to the engineers that i'm experiencing the very same issue on an Intel NUC with 4400 Graphics (BOXD34010WYKH).Windows 8.1, latest BIOS and drivers. I'd like to see this issue...
View ArticleClik here to view.
CDC serial/Arduino stops working on Windows if more than 50 Edison boards
I guess this is a very good problem to have, but here is a curious sighting:Every time one connects a new Edison board to a Windows PC (I have windows 7 but I doubt they fixed it with 8/8.1), Edison...
View ArticleIntel(R) HD Graphics 4000 Lap Top Freeze/Chrash
Hello Guys! I have a big Problem!My Lap Top is chrashing and freezing using my Intel HD Graphics! I was testing around and trying everything to stop the Freezes and Crashes on my System.I Managed to...
View ArticleRe: How best proceed with overheating i7-4790K?
Thanks ken-Intel for your helpful advice and encouragement. I have unmarked your previous as correct answer and instead marked the post with the link as correct so people can find the document easily,...
View ArticleRe: How best proceed with overheating i7-4790K?
Vitoi - As I understand it, to determine whether your CPU is overheating for sure you need to compare like for like with the same settings as kens and the same test and version of XTU and see if you...
View ArticleRe: PXE BOOT AFTER SYSPREP?
Thank you Kevin.I should have added in the OP that sysprep is run with the /generalize switch.
View ArticleRe: why my new ssd drive intel 520 120GB shows that already worked ,power on...
This is not correct. Both drives are also affected by the bug. See the "Raw Values" column of ID 9. The hours are encoded in the lower 4 bytes:000DA76E hex = 894830 decimal000DA77C hex = 894844 decimal...
View ArticleRe: Cannot find /dev/cu.usbserial[n] when flashing Edison on Mac OS X Yosemite
Please note: there are two USB connectors on the breakout board:- The lower one which allows to see Edison 800 MB update partition as a VFAT-32 drive. The drive is only good for copying the latest...
View ArticleDH87MC system start problem
I am assembling a desktop. My system configuration that I have purchased is :Motherboard: DH87MCProcessor: i5 4440Ram:Corsair Vengeance DDR3 4GB Ram (CMZ4GX3M1A1600C9) After assembling, (did it exactly...
View ArticleClik here to view.
Re: SATA RAID Controller update
Hello Sylvia, Attached you may see a picture with my "RST option ROM" verision.
View ArticleRe: DH87MC system start problem
You will get a better response in Desktop Boards forum.I have moved your post there. Doc
View ArticleClik here to view.
Re: Connecting Edison to WIFI
mhahn, in the latest official image, udhcpd is loaded by the wpa_supplicant_event.service with systemd. AriGold, that google link we are wanting for in reply 90 to your router manual has been posted at...
View ArticleRe: npm usb binding problem on Edison
I'm still stuck. I am running node 0.10.32, I have libusb-1.0.9 and libusb-1.0-dev, and the npm module usb v0.3.11. The git hub issue ( Binding issue on Linux · Issue #37 · nonolith/node-usb · GitHub...
View ArticleRe: How to set Python Environment prior to login so can run a python program...
something like cat > /home/root/display_ip.py <<EOF #! /usr/bin/env python import pyupm_i2clcd as lcd x = lcd.Jhd1313m1(0, 0x3E, 0x62) import subprocess...
View Article