Clik here to view.
Will wearables steal the show at CES 2014?
Wearable technology will be everywhere throughout the enormous CES showroom floor, according to Geoff Blaber, vice president of research at CCS Insight. "This year it will be about super low cost...
View ArticleDG45FC Memory Limit
When I built my DG45FC m/b desktop at an Intel Channel Conference in Garden City, Long Island, New York It came with a single 2 Gbyte Kinston Ram in one of two available slots. This was great for...
View ArticleCan't get audio to work
Hi, I have windows 8.1 installed on my d34010wyk NUC HTPC connected to a samsung smart TV with HDMI cable. The problem is I can't get audio to work. The digital audi source shows as unplugged. I know...
View ArticleRe: DG45FC Memory Limit
It appears that the board does support 8gb. Please review this document: http://downloadmirror.intel.com/15992/eng/DG45FC_SpecUpdate07.pdfspecifically section 1.5 of page 9, and table 1 on page 8. The...
View ArticleRe: D2500CC, how do I set mac address in DOS or BIOS???
PowerFlower, The MAC address for the primary LAN port is indeed stored in the BIOS flash (for secondary LAN/WLAN interfaces, though, EEPROMs are typically used). We program the MAC Address into the...
View ArticleClik here to view.
Re: Will wearables steal the show at CES 2014?
I got a Pebble for Christmas, the tech is pretty basic but it is making me more productive getting notifications sooner. I'm only a couple weeks in to the "trial" but so far I love it. Excited to see...
View ArticleRe: Can I start a sketch that is stored on a USB drive?
I liked all of this and the direction headed.on a separate note, does the sd card actually let you create a new non-existing file?
View ArticleRe: Workaround for SD file creation bug.
Excellent... I mean super. I was following your other thread where it says it is a known issue and when I searched to get back there happily found this. Any idea when the update will be out? and where...
View ArticleD54250WYK1: Unknown Device ACPI\MSFT0101
erA fresh install of Windows 7 Professional SP1 x64. After installing all of the device drivers from the NUC Pack (November 2013) I have this one device left: ACPI\MSFT0101*MSFT0101 Search Results come...
View ArticleRe: getting started: monitor shell?
OK, I figured Ethernet would work, but wasn't sure how to figure out the IP address without some shell running, at least for the first time. I'll read the thread, or resort to the serial interface. I...
View ArticleWhat is the correct link for software downloads?
alileThis link is incorrect:https://communities.intel.com/community/makers/software/drivers This link is correct:https://communities.intel.com/community/makers/drivers
View ArticleRe: Problem with HDMI audio using intel hd 4600 graphics
Noticed that when my Home Theater is off, the sound panel detects my TV, as soon as I turn it on it disappears. When I turn it off again the TV appears back. This is an Emotiva UMC-200 Home Theater...
View ArticleRe: laptop dell i7 issue
That is a valid troubleshooting step too…I would escalate the issue with the system manufacturer.
View ArticleRe: Support for SSL connections through Wi-Fi
Hi OzzieG, I believe you can set up an SSL connection on the Galileo via Linux. I’m not sure if it’s supported though a sketch. Regards,Intel_JEspinoza
View ArticleRe: 530 SSD freezes & kills computer after a few minutes?
I do not think so; the drive does not appear in BIOS after a system restart.I believe the best chance is to update the BIOS.
View ArticleRe: Need Clarification Regarding Socket Types
Hi, Not sure if this helps but....You need 1st to pay attention to socket supported. The package size will be in line with the socket. The i3-330m only works in g1 (rPGA988A) sockets but as to your...
View ArticleRe: BIOS recovery not working
I am having the same problem I googled this problem and found no solution to it. Couple of other people also posted the same problem on intel community and still there problem hasn't been solved.
View ArticleSystem is in manufacturing mode
Dear All: The BIOS screen on a DG41TY board is showing the following message: System is in manufacturing mode. The BIOS is current, but I reloaded the BIOS just in case it was corrupted. The message is...
View ArticleRe: getting started: monitor shell?
Not related to this topic. I'm trying to figure out how to compile / download code now. Is there cc/gcc cross-compile, or do I have to do everything through the Arduino IDE? Only just starting to...
View Article